思科 静态链路聚合 实验

第一步 给 PC 配 ip

第二步 划分 vlan

进入左侧 交换机 1

Switch>
Switch>en
Switch#conf
Configuring from terminal, memory, or network [terminal]? 
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 2      //创建 vlan 2
Switch(config-vlan)#e
Switch(config)#vlan 3      //创建 vlan 2
Switch(config-vlan)#e
Switch(config)#
// vlan 划分完成 下一步 划分vlan 绑定给 端口
Switch(config)#interface fastEthernet 0/1     //进入端口 1 
Switch(config-if)#sw mo ac                   //设置端口模式为 access
Switch(config-if)#sw ac vlan 2             //ac模式划分到vlan 2
Switch(config-if)#exit           //退出 重复
Switch(config)#interface fastEthernet 0/2
Switch(config-if)#sw mo ac 
Switch(config-if)#sw ac vlan 3
Switch(config-if)#e
Switch(config)#

进入右侧 交换机 2

Switch>
Switch>en
Switch#
Switch#conf
Configuring from terminal, memory, or network [terminal]? 
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 2
Switch(config-vlan)#e
Switch(config)#vlan 3
Switch(config-vlan)#e
Switch(config)#interface f0/1
Switch(config-if)#sw mo ac
Switch(config-if)#sw ac vlan 2
Switch(config-if)#e
Switch(config)#interface f0/2
Switch(config-if)#sw mo ac
Switch(config-if)#sw ac vlan 3
Switch(config-if)#e
Switch(config)#

第三步 绑定22-24端口 创建链路

进入 交换机 1

Switch(config)#interface range fastEthernet 0/22-24      //进入端口22-24
Switch(config-if-range)#channel-group 1 mode on        //创建链路 1
Switch(config-if-range)#
Creating a port-channel interface Port-channel 1
%LINK-5-CHANGED: Interface Port-channel 1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up
Switch(config-if-range)#exit          //退出操作
Switch(config)#interface port-channel 1      //进入链路 1
Switch(config-if)#sw mo trunk                //设置链路模式为 trunk
Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up
Switch(config-if)#sw trunk all vlan 2,3      //将vlan 2，3绑定到链路 1
Switch(config-if)#exit                       //退出操作
Switch(config)#

进入 交换机 2 重复相同操作

Switch(config)#interface range fastEthernet 0/22-24      //进入端口22-24
Switch(config-if-range)#channel-group 1 mode on        //创建链路 1
Switch(config-if-range)#
Creating a port-channel interface Port-channel 1
%LINK-5-CHANGED: Interface Port-channel 1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up
Switch(config-if-range)#exit          //退出操作
Switch(config)#interface port-channel 1      //进入链路 1
Switch(config-if)#sw mo trunk                //设置链路模式为 trunk
Switch(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel 1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/22, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, changed state to up
Switch(config-if)#sw trunk all vlan 2,3      //将vlan 2，3绑定到链路 1
Switch(config-if)#exit                       //退出操作
Switch(config)#

实验结束 ，接下来测试是否 通过

测试 标准 同 vlan 可ping通 不同vlan 不通

感谢你的阅读和观看！

点击数：46